
Cracked crowns, failed flashing and leaky flues fixed right
Chimney repair Charlotte NC that stops leaks for good
When you need chimney repair Charlotte NC homeowners can count on, we get it done fast. We fix chimney leaks, cracked crowns, spalling brick and failed flashing on homes across Mecklenburg County. If water is staining your ceiling or your flue has seen better days, call (888) 403-0810 and we will stop the damage before it spreads.
What's included
What our chimney repair service includes
Every chimney repair starts with a full inspection, and the written scope tells you exactly what is covered. Here is what is typically part of a standard chimney repair job. If your chimney needs a flue liner, a full rebuild or masonry work beyond repointing, we price that separately and show you why.
Full chimney inspection
We inspect the crown, cap, flue tiles, mortar joints, step flashing, counter flashing and the roof deck around the chase. A 15-minute water test pinpoints the leak entry so the repair targets the actual problem.
Crown repair or rebuild
Cracked crowns get rebuilt with a 2-inch overhang and a drip edge that sheds water away from the brick. Small hairline cracks get cleaned and sealed with masonry-rated sealant.
Flashing replacement
We remove failed step and counter flashing, install new metal flashing cut into the shingle courses, and seal with polyurethane caulk. Ice and water shield goes under the transition for a second layer of protection.
Mortar repointing
Soft or crumbling mortar joints get ground out to the proper depth and repointed with a mortar mix matched to your brick. This stops water from wicking into the wall and freezing.
Cap and chase cover work
Rusted chase covers and damaged caps get replaced with stainless or copper units sized to your flue. A proper cap keeps rain, birds and debris out of the flue year-round.
Cleanup and final test
We sweep the roof and driveway with a magnetic sweeper, haul off all debris, run a second water test and walk you through the finished work with photos.
Service overview
Chimney repair Charlotte NC done by roofers who know chimneys
Chimney repair Charlotte NC is the trade of rebuilding, sealing and re-flashing the parts of a chimney that fail first: the crown, the mortar joints, the cap and the flashing where the stack meets your roof. We tear out cracked crowns, repoint spalling brick, replace rusted chase covers and install new step and counter flashing tied into your shingles. Most repairs take two to six hours and are finished the same day we start.
Charlotte chimneys take a beating. Summer storms drive rain sideways into mortar, winter freeze-thaw cycles pop bricks loose, and our red clay soil shifts footings just enough to open hairline cracks. If you spot water in the firebox or a rust streak on the ceiling, that is usually flashing failure, not a roof leak. We handle chimney leak repair Charlotte NC for homes from Uptown to Ballantyne, and we tell you straight whether you need a patch or a rebuild.
The service timeline
How our chimney repair process works
The process flexes to the condition, but these checkpoints keep decisions clear.
Call and schedule
Call (888) 403-0810 or book online. We ask what you are seeing, water in the firebox, a ceiling stain, loose brick, and set a two-hour arrival window. Most Charlotte-area inspections happen within 48 hours, and same-day chimney repair Charlotte NC is available for active leaks.
Roof and attic inspection
We get on the roof and into the attic. We check the crown, cap, flue tiles, step flashing, counter flashing and the decking around the chase. A 15-minute water test tells us exactly where the water is entering, so we are not guessing.
Written scope and price
You get a written scope with a fixed price before any work starts. If we find rot in the framing or a failed flue liner, we show you photos and price that separately. No pressure, no same-day-only discount games.
Repair day
Our crew arrives with a ladder stabilizer, roof safety harness and magnetic sweeper to protect your driveway. We rebuild the crown, repoint mortar, replace flashing and reseal the cap. Typical repairs run two to six hours, and we clean up with a magnet sweep before we pull out.
Final test and walkthrough
We run a second water test to confirm the leak is gone, then walk you around the chimney and show you the new crown, flashing and sealant lines. You get photos of the finished work and a 5-year workmanship warranty on the repair.
Tools & methods
Tools and methods we use on every chimney repair
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Roof safety harness and ladder stabilizer
Keeps our crew anchored and the ladder stable on steep Charlotte roof pitches. Every chimney job starts with fall protection, no exceptions.
Caulking gun with polyurethane masonry sealant
Applies the sealant bead at flashing edges and mortar joints. We use polyurethane, not silicone, because it bonds to masonry and holds up to UV and freeze-thaw.
Pry bar and roofing hammer
Lifts shingle courses and sets flashing without tearing the surrounding roof. Clean removal is what lets us tie new flashing into the existing roof correctly.
Chalk line and utility knife
Marks straight cut lines for flashing and underlayment. Straight lines matter when the repair has to blend into the existing shingle pattern.
Magnetic sweeper
Sweeps the driveway, walkway and lawn for roofing nails after the job. We run it twice before we leave, because a nail in a tire is a bad way to end a repair.
Roofing nail gun
Fastens shingles and underlayment back down after flashing work. We set the depth so nails seat flush without cutting into the shingle mat.
Use cases
When Charlotte homeowners call us for chimney repair
These examples show how the service framework adapts rather than forcing every call through one repair.

Flashing replacement in Ballantyne
A 2008 home had a ceiling stain spreading 18 inches from the chimney chase. The step flashing had rusted through and the counter flashing was sealed with smeared tar that had dried and cracked. → We removed the failed flashing, installed new step and counter flashing cut into the shingle courses, added ice and water shield at the transition and sealed with polyurethane. The stain stopped growing within a week and the ceiling was patched and painted.
Chase cover and cap replacement in University City
A 1995 home had a rusted chase cover with holes the size of a quarter. Rain was running straight into the flue, rusting the damper and soaking the firebox floor. The homeowner had not used the fireplace in two years. → We measured the flue, installed a new stainless chase cover and cap, cleaned and sealed the firebox, and replaced the rusted damper. The homeowner used the fireplace that winter with no water issues.
Problems we solve
Chimney problems we fix for Charlotte homeowners
Most chimney calls we get in Charlotte fall into a handful of categories. Here are the ones we see most, what happens if you ignore them, and how we fix them.
Water dripping into the firebox during rain
We run a water test to find the entry point, usually failed step flashing or a cracked crown. We replace the flashing, rebuild the crown if needed, and reseal the chase. Most of these are done in a single visit.
Crumbling mortar joints and spalling brick
We grind out the soft mortar to the correct depth and repoint with a mix matched to your brick. If spalling has gone too deep, we rebuild the affected courses and tie them back into sound masonry.
Rusted chase cover or missing chimney cap
We measure the flue and install a stainless or copper cap or chase cover sized to fit. It keeps water and animals out and gives you a serviceable access point for future inspections.
Chimney leak showing up as a ceiling stain
We open up the area, find the leak source, replace any rotted decking and install new flashing and underlayment. We document the repair with photos so you have a record for insurance if needed.
Pricing process
What chimney repair costs in Charlotte in 2026
$350 - $1,800 depending on scope
Scope of the failure
A single flashing replacement is a few hours of work. A crown rebuild with repointing is a full day. The bigger the failed area, the higher the price, and we tell you which one you are looking at after the inspection.
Chimney height and roof pitch
A tall chimney on a steep roof takes longer to access safely and requires more fall protection setup. That labor is part of the price, and it is not negotiable for safety reasons.
Material selection
Stainless and copper caps and chase covers cost more than painted steel but last two to three times as long. We show you both options and let you decide based on how long you plan to stay in the home.
Questions before we arrive
Frequently asked questions about chimney repair in Charlotte

How much does chimney repair cost in Charlotte NC?
Most chimney repairs in Charlotte run $350 to $1,800 in 2026, depending on scope. A flashing replacement typically lands around $450 to $850. A full crown rebuild with repointing runs $900 to $1,800. Structural rebuilds or flue liner replacement start higher. We give you a fixed written price after the inspection, so you know the number before we start.
Why is my chimney leaking in North Carolina?
In Charlotte, nine out of ten chimney leaks come from failed flashing, a cracked crown or open mortar joints. Our summer storms drive rain sideways into the masonry, and freeze-thaw cycles in January open cracks wider. Water in the firebox almost always means the flashing at the roof transition has failed, not the flue itself. A water test confirms it in 15 minutes.
Who repairs chimneys near me in Charlotte?
We do. Roofing Repair Charlotte handles chimney repair across Mecklenburg County, including Uptown, Dilworth, South End, NoDa, Plaza Midwood, Myers Park, Ballantyne and University City. Call (888) 403-0810 and we will schedule an inspection, usually within 48 hours. Same-day service is available for active leaks.
Can you fix a cracked chimney in Charlotte NC?
Yes. Hairline cracks in the crown or mortar joints get repointed and sealed with masonry-rated sealant. Larger cracks in the brick itself may need partial rebuild of the affected courses. We inspect the flue tiles too, because a cracked flue liner is a fire hazard and needs a stainless liner or rebuild, not just a surface patch.
Ready when you are
Get your chimney repair Charlotte NC scheduled today
Water in the firebox or a stain on the ceiling will not fix itself. Call (888) 403-0810 and we will inspect your chimney, give you a fixed written price and get the repair done, often the same day. Licensed, insured and warrantied for 5 years.

Talk with the local team
Request Chimney Repair
Call, text, or send us a message and we'll get back to you fast. Our phones are answered 24/7 for emergencies, and standard estimates are usually scheduled the same day. Tell us what's going on with your roof and we'll take it from there.


