Skylight Installation in Charlotte: roofer applying specialized flashing tape around the perimeter of a newly installed

Velux units, code-correct flashing, and a dry ceiling for decades

Skylight Installation Charlotte NC done leak-free the first time

If you want more daylight in a dark hallway, stairwell, or kitchen, skylight installation Charlotte NC is the fastest way to get it without adding square footage. We cut the opening, frame it, set a Velux unit, and flash it to Mecklenburg County code so it never drips. Whether you're in a 1920s bungalow in Plaza Midwood or a newer build in Ballantyne, we handle the whole job in one day.

Live phone supportUpfront optionsBacked workmanship
Call firstLive triage can help before arrival
Safety before speedRisks assessed before work begins
Diagnose the causeWe trace the source, not just the symptom
Approve the workScope and price explained upfront

What's included

What's included in a skylight installation

Every install we do includes the structural opening, the unit, the flashing, and the interior finish. We don't quote a skylight and then nickel-and-dime you on the light well or the permit. Here's what's in the box.

01

Structural opening and framing

We cut the roof deck, frame the opening with 2x6 or 2x8 headers, and sister any rafter we cut. The opening is sized to the unit, not the other way around, so the light lands where you actually want it.

02

Velux unit and flashing kit

We supply Velux fixed or venting units with the matching factory flashing kit. The kit includes step flashing, head flashing, and the sealant details that keep water out for the life of the roof.

03

Ice and water shield

A full ice and water shield membrane goes around the curb and up under the surrounding shingle courses. In Charlotte's summer storms, this is the layer that saves you when a shingle gets displaced.

04

Interior light well finish

We insulate the shaft, install drywall or a pre-finished light well, and tape and mud the seams. You get a clean, paintable surface, not a raw hole with exposed framing.

05

Mecklenburg County permit

We pull the building permit and schedule the inspection. Structural roof cuts require it in Mecklenburg County, and we handle the paperwork so you don't have to chase the county.

06

Water test and cleanup

Before we leave, we run water on the roof above the unit for 20 minutes and check the attic and ceiling. A magnetic sweeper goes across the lawn and driveway for nails, and we haul off all debris.

Service overview

What skylight installation Charlotte NC actually involves

Skylight installation Charlotte NC is the process of cutting a framed opening through your roof deck, building a curb or setting a deck-mount frame, tying the unit into the roof with a skylight flashing kit, and sealing it against rain and heat. It's not a handyman job. You're cutting a hole in the one thing that keeps water out of your house, so the flashing detail matters more than the glass. We use Velux units, ice and water shield around the curb, and step flashing that laps under the shingles above and over the courses below.

Most Charlotte homeowners call us for one of three reasons: a dark room that never gets enough light, a builder-grade acrylic dome that has yellowed and cracked, or a new roof going on and they want to add a skylight while the shingles are already off. If you're pricing skylight installation near me Charlotte NC, the smart move is to bundle it with a roof replacement so you're not paying twice for tear-off and disposal. We work across Mecklenburg County and know how these units behave in our humidity and summer heat.

Daylight without new wallsA 2x4-foot fixed skylight throws roughly three times the light of a same-size vertical window because it faces the sun directly. In a Dilworth bungalow with a dark central hallway, one unit can replace a lamp you've been running all day. No framing changes, no exterior wall work, no new siding.
Venting cuts attic heatA venting skylight paired with ridge vents drops attic temps 15 to 25 degrees on a July afternoon in Charlotte. That's less strain on your HVAC and a cooler second floor. We size the vent to the room, not the roof, so you get airflow where you actually feel it.
Bundled with a new roofIf your asphalt shingles are already coming off for a replacement, adding new skylight installation Charlotte NC during the same job saves you the second tear-off, the second dumpster, and the second day of labor. Most homeowners save $400 to $900 by bundling instead of scheduling separately.
Roofing in Charlotte: Close-up of a roofer's gloved hands operating a pneumatic roofing nail gun to secure an asphalt shingle
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.

The service timeline

How our skylight installation process works

The process flexes to the condition, but these checkpoints keep decisions clear.

01

On-site measure

We walk the attic first, not the roof. We need to see rafter spacing, insulation depth, and whether a chase or duct runs through your planned location. Then we chalk line the opening from below so you can stand in the room and see exactly where the light will land. Takes 30 to 45 minutes.

Stage 1
02

Cut and frame

We cut the roof deck with a circular saw set to the shingle depth, then frame the opening with 2x6 or 2x8 headers tied into the rafters. A roofing hammer and pry bar handle the shingle removal around the cut. We never cut a rafter without sistering it back to full load capacity.

Stage 2
03

Set the unit and flash

The Velux unit drops onto a curb or deck-mount frame, and we install the skylight flashing kit in the correct sequence: ice and water shield first, then step flashing, then the head flashing at the top. This is the step that decides whether you get a leak in year two or year twenty.

Stage 3
04

Interior finish

We insulate the shaft, install drywall or a pre-finished light well, and tape and mud the seams. Most homeowners paint after we leave, but we can match texture on request. The room goes from a framed hole to a finished ceiling in about half a day.

Stage 4
05

Water test and cleanup

Before we pack up, we run a hose on the roof for 20 minutes directly above the unit and check the attic and ceiling for moisture. Then a magnetic sweeper goes across the lawn and driveway for nails. You get a walkthrough, a photo record, and a written workmanship warranty.

Stage 5

Tools & methods

Tools and methods we use on every install

Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.

01

Roofing nail gun

Drives shingle nails to consistent depth and angle around the skylight curb. Hand-nailing around flashing leads to over-driven or under-driven nails, which is where leaks start.

02

Pry bar and roofing hammer

Lifts and resets the shingle courses around the opening without tearing the mat. We need clean shingle edges to lap the step flashing correctly.

03

Chalk line

Marks the opening from inside the room so you can see exactly where the light will land before we cut. No guessing, no surprises after the drywall comes down.

04

Caulking gun

Applies sealant at the head flashing and any vertical joint. We use a roofing-grade sealant that holds up to Charlotte's UV and thermal cycling.

05

Roof safety harness and ladder stabilizer

OSHA-compliant fall protection on every roof, plus a stabilizer so the ladder doesn't shift while we're carrying a Velux unit up.

06

Magnetic sweeper

Runs across the lawn and driveway at the end of every job to pick up stray roofing nails. Standard practice, not an upsell.

07

Utility knife and shingle cutter

Trims shingles and underlayment to fit tight around the curb. Clean cuts mean the flashing laps flat instead of puckering.

Use cases

When Charlotte homeowners call us for skylights

These examples show how the service framework adapts rather than forcing every call through one repair.

Roofing in Charlotte: team of roofers working together to hoist a large bundle of shingles onto a residential rooftop using
Dark Dilworth hallway gets a 2x4 VeluxA 1948 bungalow with a central hallway that had no exterior wall for a window. The homeowner ran two lamps all day and the room still felt like a cave. Ceiling was original plaster with no attic access. → We cut a 2x4 opening, sistered two rafters, set a fixed Velux unit, and finished the light well in one day. The hallway now reads as naturally lit from morning to late afternoon. No lamps needed.

Ballantyne dome swap stops a ceiling leak

A 2004 build with a builder-grade acrylic dome that had yellowed and cracked at the curb. Water was staining the guest bath ceiling and soaking the insulation above it. Homeowner had patched it twice with caulk. → We removed the dome, replaced the curb, installed a Velux glass unit with a new flashing kit and ice and water shield, and water-tested for 20 minutes. Leak stopped, light transmission jumped back to full, ceiling repaired.

Myers Park roof replacement with two skylights

A homeowner scheduling a full roof replacement on a 1960s home with two failing skylights. Both units leaked, the flashing was rusted, and the shingles were at end of life. Separate quotes would have meant two tear-offs. → We bundled the skylight install with the roof replacement, cut and flashed both units while the deck was exposed, and passed Mecklenburg County inspection first try. Homeowner saved $700 versus scheduling separately.

Problems we solve

Problems a skylight install solves for Charlotte homes

Most of our skylight calls come from homeowners dealing with one of these four issues. If any of them sound familiar, an install or replacement is usually the fix.

ISSUE

Dark rooms that never get enough natural light

We chalk line the opening from inside so you can see exactly where the light lands before we cut. A single 2x4 fixed unit typically transforms a hallway, stairwell, or kitchen. Most installs are done in one day.

SYMPTOM

Old acrylic domes that have yellowed or cracked

We replace the dome with a Velux glass unit and re-flash the curb with a new skylight flashing kit. The upgrade is usually a half-day job and drops your leak risk to near zero.

SIGN

Skylight leaks that keep coming back

We trace the leak to the source, usually failed flashing or a dried-out sealant bead, not the unit itself. We re-flash with ice and water shield and step flashing, then water-test before we leave. Most repairs are done in a single visit.

ALERT

Attic heat that drives up summer cooling bills

A venting skylight paired with ridge vents and soffit intake drops attic temps 15 to 25 degrees. We size the vent to the room and balance the intake so air actually moves instead of just sitting there.

Pricing process

What skylight installation costs in Charlotte

$1,800 - $3,500 for a single-unit install, all-in

Phase 01

Fixed versus venting unit

A fixed Velux unit costs less and does one job: let light in. A venting unit adds a motor or manual crank, a screen, and more complex flashing, which typically adds $500 to $1,200 to the installed price.

Phase 02

Unit size and glass type

A 2x4 unit is the standard size and the cheapest to install. Going to 2x6 or 4x4 means more framing, more flashing, and a bigger opening. Laminated or low-E glass adds cost but cuts heat gain and UV fading.

Phase 03

Roof pitch and access

A steep pitch or a two-story roof slows the work and requires more safety rigging. A shallow pitch on a single-story ranch is faster. We tell you which category your roof falls into during the estimate.

Questions before we arrive

Skylight questions Charlotte homeowners ask us

Roofing in Charlotte: roofer inside an attic, installing a new roof ventilation baffle between rafters
Call (888) 403-0810
How much does skylight installation cost in Charlotte NC?

Most single-unit installs run $1,800 to $3,500 in 2026, depending on unit size, fixed versus venting, and whether the interior finish is included. A basic 2x4 fixed Velux with a standard light well lands near the low end. Venting units, larger sizes, and complex roof pitches push toward the top. Bundling with a roof replacement usually saves $400 to $900.

Can you install a skylight without replacing the roof in Charlotte North Carolina?

Yes, if your shingles have at least five years of life left and the decking around the opening is solid. We inspect the surrounding courses first. If the shingles are brittle or already curling, we'll recommend waiting and bundling the skylight with your next replacement. Cutting into a failing roof just creates a leak path you didn't have before.

Do skylights leak in Charlotte NC?

A properly flashed skylight doesn't leak, even in our summer thunderstorms and hurricane remnants. Leaks almost always trace to bad flashing, a failed sealant bead, or a cracked acrylic dome, not the unit itself. We use Velux flashing kits and ice and water shield on every install, and we water-test before we leave the property.

Who installs skylights near me in Charlotte?

You want a licensed roofing contractor, not a general handyman. Skylight work involves cutting rafters, pulling a Mecklenburg County permit, and flashing to code. Roofing Repair Charlotte has been installing skylights since 2020 and holds GAF Master Elite and Owens Corning Preferred credentials. Call (888) 403-0810 for a free on-site estimate.

Ready when you are

Get your skylight installation Charlotte NC estimate

We'll walk your attic, chalk line the opening from inside, and give you a written price before any work starts. Licensed, insured, and warrantied. Call (888) 403-0810 or book online and we'll be on your roof this week.

Roofing in Charlotte: roofer carefully inspecting a residential roof for storm damage, pointing to a damaged shingle with a

Talk with the local team

Request Skylight Installation

Call, text, or send us a message and we'll get back to you fast. Our phones are answered 24/7 for emergencies, and standard estimates are usually scheduled the same day. Tell us what's going on with your roof and we'll take it from there.

Main St, Charlotte, North CarolinaMain office · technicians serve the full area
Call now